|
|
|
Download
Brochure (pdf, 237 kB) |
|
ZB100F
BLACK LIGHT
(pdf, 192 kB) |
ZB 250
BLACK LIGHT
(pdf, 138 kB) |
ZB-35BP
BLACK LIGHT SYSTEM
(pdf,
148 kB) |
ΗΛΕΚΤΡΟΜΑΓΝΗΤΗΣ Y6
(pdf, 720 kB) |
ΗΛΕΚΤΡΟΜΑΓΝΗΤΗΣ Y7
(pdf,
177 kB) |
ΗΛΕΚΤΡΟΜΑΓΝΗΤΗΣ Y8
(pdf, 475
kB) |
ΜΟΝΙΜΟΙ ΜΑΓΝΗΤΕΣ
(pdf, 1.04 MB) |
ΗΛΕΚΤΡΟΝΙΚΟ ΜΑΓΝΗΤΟΜΕΤΡΟ
MAGMETER MODEL GM04
(pdf, 169 kB) |
ΡΑΔΙΟΜΕΤΡΟ - ΦΩΤΟΜΕΤΡΟ MK-V1
(pdf, 209 kB) |
|
MAGNETIC FLOW /COIL TEST
PIECES
RPS700
BS6072 |
CURRENT FLOW TEST PIECES
0-1000A: BS6072, RPS700
1000-3000A: RPS700
3000 5000A: RPS700 |
MAGNETIC PARTICLE TEST
PIECE
Contains course and fine artificial
surface and sub-surface defects in both directions. Meets or exceeds
most specifications for artificial test specimens including
MIL-STD-271 |
|
TEST BLOCKS
Wet residual go/no go test block which
provides a quick check on quality.
A wet continuous test block
is also available. |
KETOS TEST RING
The ketos ring has a number of
artificial defects for both Dry Powder and Wet Method and meets ASTM
E1444 |
BERTHOLD PENETRAMETER
Checks magnetization, penetration depth,
quality of fluorescent suspension and magnetic field direction |
|
ASME FIELD INDICATOR
Used to gauge the strength and direction
of the magnetic field in accordance with ASME Boiler and Pressure
Vessel Code Section V |
FIELD INDICATOR
Magnetometer used to determine if a
component is magnetized |
CALIBRATED FIELD INDICATOR
Scaled to +/- 20 gauss from
zero for determining the level of residual magnetism to 5% of
full-scale reading.
Available scaled to +/- 10
gauss. |
|
CENTRIFUGE TUBE & STAND
Essential items in
ascertaining bath concentration. Centrifuge Tube meets the
requirements of ASTM D96 and BS4069. |
MAGNETIC INDICATOR STRIPS
Used to provide a guide to
the strength of the magnetic field at the precise point of their
location.
Complies with BS4142 and
BS6072.
Type 1 for general use.
Type II for aerospace work. |
REFRACTOMETER
A hand held optical
instrument used for measuring the concentration of hydrophilic
removers in water. In operation, a small sample of the solution is
applied to the prism face; readings are then taken by looking into
instrument at the built-in scale. |
|
Ni-Cr TEST PANELS
A range of process control
panels having finely controlled crack depths to offer greater
discrimination when comparing penetrant sensitivity. Matched pairs of
panels are used to study the effects of process change. Available in
pairs, in the following crack sizes 10 - 20 - 30 - 50 Microns. Kit one
pair of each size. |
TAM PANEL
A stainless steel panel to
monitor both sensitivity and washability of penetrants. It provides a
grit blasted surface for washability tests and a chromed section with
5 star shaped defects ranging in size from course/fine. Meets the
requirements of Pratt & Whitney (TAM 146040) |
TAM PANEL
A stainless steel panel to
monitor both sensitivity and washability of penetrants. It provides a
grit blasted surface for washability tests and a chromed section with
5 star shaped defects ranging in size from course/fine. Meets the
requirements of Pratt & Whitney (TAM 146040) |
|
STAINLESS STEEL TEST BLOCK
Monitors WASHABILITY of
water washable or post emulsified penetrants. May be used repeatedly
if thoroughly cleaned after each use. |
TAM CRACK COMPARATORS
A transparent crack
comparator covering the Range 0.2mm – 4.6mm increments which also
meets the requirements of Pratt & Whitney (TAM 135273).
Also available: A general
purpose crack comparator having increments from 0.12mm – 3.0mm |
CONTRAST CONTROL SPECTACLES
Specifically designed to
eliminate long wave UV(A) and protect the eyes during excessive
periods under ultraviolet lighting, these spectacles also reduce
fatigue and provide an optimum contrast in viewing. |
|
|
|
Download
Brochure (pdf, 237 kB) |
